Next: Component_Size Clauses, Previous: Biased Representation, Up: Representation Clauses and Pragmas
In Ada 95, T'Size for a type T is the minimum number of bits
required to hold values of type T. Although this interpretation was
allowed in Ada 83, it was not required, and this requirement in practice
can cause some significant difficulties. For example, in most Ada 83
compilers, Natural'Size was 32. However, in Ada 95,
Natural'Size is
typically 31. This means that code may change in behavior when moving
from Ada 83 to Ada 95. For example, consider:
type Rec is record;
A : Natural;
B : Natural;
end record;
for Rec use record
at 0 range 0 .. Natural'Size - 1;
at 0 range Natural'Size .. 2 * Natural'Size - 1;
end record;
In the above code, since the typical size of Natural objects
is 32 bits and Natural'Size is 31, the above code can cause
unexpected inefficient packing in Ada 95, and in general there are
cases where the fact that the object size can exceed the
size of the type causes surprises.
To help get around this problem GNAT provides two implementation
defined attributes, Value_Size and Object_Size. When
applied to a type, these attributes yield the size of the type
(corresponding to the RM defined size attribute), and the size of
objects of the type respectively.
The Object_Size is used for determining the default size of
objects and components. This size value can be referred to using the
Object_Size attribute. The phrase “is used” here means that it is
the basis of the determination of the size. The backend is free to
pad this up if necessary for efficiency, e.g. an 8-bit stand-alone
character might be stored in 32 bits on a machine with no efficient
byte access instructions such as the Alpha.
The default rules for the value of Object_Size for
discrete types are as follows:
Object_Size for base subtypes reflect the natural hardware
size in bits (run the compiler with -gnatS to find those values
for numeric types). Enumeration types and fixed-point base subtypes have
8, 16, 32 or 64 bits for this size, depending on the range of values
to be stored.
Object_Size of a subtype is the same as the
Object_Size of
the type from which it is obtained.
Object_Size of a derived base type is copied from the parent
base type, and the Object_Size of a derived first subtype is copied
from the parent first subtype.
The Value_Size attribute
is the (minimum) number of bits required to store a value
of the type.
This value is used to determine how tightly to pack
records or arrays with components of this type, and also affects
the semantics of unchecked conversion (unchecked conversions where
the Value_Size values differ generate a warning, and are potentially
target dependent).
The default rules for the value of Value_Size are as follows:
Value_Size for a base subtype is the minimum number of bits
required to store all values of the type (including the sign bit
only if negative values are possible).
Value_Size as the first subtype. This is a
consequence of RM 13.1(14) (“if two subtypes statically match,
then their subtype-specific aspects are the same”.)
Value_Size corresponding to the minimum
number of bits required to store all values of the subtype. For
dynamic bounds, it is assumed that the value can range down or up
to the corresponding bound of the ancestor
The RM defined attribute Size corresponds to the
Value_Size attribute.
The Size attribute may be defined for a first-named subtype. This sets
the Value_Size of
the first-named subtype to the given value, and the
Object_Size of this first-named subtype to the given value padded up
to an appropriate boundary. It is a consequence of the default rules
above that this Object_Size will apply to all further subtypes. On the
other hand, Value_Size is affected only for the first subtype, any
dynamic subtypes obtained from it directly, and any statically matching
subtypes. The Value_Size of any other static subtypes is not affected.
Value_Size and
Object_Size may be explicitly set for any subtype using
an attribute definition clause. Note that the use of these attributes
can cause the RM 13.1(14) rule to be violated. If two access types
reference aliased objects whose subtypes have differing Object_Size
values as a result of explicit attribute definition clauses, then it
is erroneous to convert from one access subtype to the other.
At the implementation level, Esize stores the Object_Size and the
RM_Size field stores the Value_Size (and hence the value of the
Size attribute,
which, as noted above, is equivalent to Value_Size).
To get a feel for the difference, consider the following examples (note
that in each case the base is Short_Short_Integer with a size of 8):
Object_Size Value_Size
type x1 is range 0 .. 5; 8 3
type x2 is range 0 .. 5;
for x2'size use 12; 16 12
subtype x3 is x2 range 0 .. 3; 16 2
subtype x4 is x2'base range 0 .. 10; 8 4
subtype x5 is x2 range 0 .. dynamic; 16 3*
subtype x6 is x2'base range 0 .. dynamic; 8 3*
Note: the entries marked “3*” are not actually specified by the Ada 95 RM,
but it seems in the spirit of the RM rules to allocate the minimum number
of bits (here 3, given the range for x2)
known to be large enough to hold the given range of values.
So far, so good, but GNAT has to obey the RM rules, so the question is
under what conditions must the RM Size be used.
The following is a list
of the occasions on which the RM Size must be used:
Size for a type
For record types, the Object_Size is always a multiple of the
alignment of the type (this is true for all types). In some cases the
Value_Size can be smaller. Consider:
type R is record
X : Integer;
Y : Character;
end record;
On a typical 32-bit architecture, the X component will be four bytes, and
require four-byte alignment, and the Y component will be one byte. In this
case R'Value_Size will be 40 (bits) since this is the minimum size
required to store a value of this type, and for example, it is permissible
to have a component of type R in an outer record whose component size is
specified to be 48 bits. However, R'Object_Size will be 64 (bits),
since it must be rounded up so that this value is a multiple of the
alignment (4 bytes = 32 bits).
For all other types, the Object_Size
and Value_Size are the same (and equivalent to the RM attribute Size).
Only Size may be specified for such types.